Housing

Rear axle center assembly without flange. 1:3.27.

To rear axle housing. Rear axle housing with differential. Left rear axle housing.

1.3 mm as required. 1.30 mm.

1.4 mm. 1.40 mm. 1.40 mm as required. 1.40 mm.

1.25 mm as required. 1.25 mm.

1.45 mm.

1.65 mm.

Rear axle output.

Rear axle output.

Ring Gear and Pinion

1:3.27.

Ring gear bearing.

As required 4.05 mm. 4.05 mm.

As required 4.15 mm. 4.15 mm.

As required 4.50 mm. 4.50 mm.

As required 3.60 mm. 3.60 mm.

As required 4.20 mm. 4.20 mm.

As required 4.00 mm. 4.00 mm.

As required 3.90 mm. 3.90 mm.

Left and right drive shaft
Inside diameter: 45mm
Outside diameter: 116mm. INTERIOR FLANGE
Inside diameter: 45mm
Outside diameter: 116mm. LEFT AND RIGHT AXLE SHAFT
Inside diameter: 45mm
Outside diameter: 116mm. Inner flange
Inside diameter: 45mm
Outside diameter: 116mm.

1.25 mm.

As required 0.9 mm. 0.90 mm.

1.35 mm.

1.10 mm.

As required 0.8mm. 0.80 mm.

0.95 mm.

As required 1.0 mm. 1.00 mm.

As required 0.7 mm. 0.70 mm.

As required 2.00 mm. 2.00 mm.

As required 1.65 mm. 1.65 mm.

As required 2.15 mm. 2.15 mm.

As required 2.30 mm. 2.30 mm.

As required 2.35 mm. 2.35 mm.

As required 1.95 mm. 1.95 mm.

As required 1.55 mm. 1.55 mm.

As required 1.50 mm. 1.50 mm.

As required 1.85 mm. 1.85 mm.

As required 1.60 mm. 1.60 mm.

As required 2.05 mm. 2.05 mm.

As required 2.45 mm. 2.45 mm.

As required 1.90 mm. 1.90 mm.

As required 2.70 mm. 2.70 mm.

As required 2,05 mm.

As required 1,80 mm.

As required 2,25 mm.

As required 1,85 mm.

As required 2,10 mm.

As required 1,55 mm.

As required 1,50 mm.

As required 1,95 mm.

As required 2,30 mm.

As required 2,00 mm.

Bearing Sleeve

Drive pinion. Pinion bearing.

Drive pinion.

100 mm.

Propeller shaft. 120 MM.

Nut

M29X1.5
Diameter: 29mm
Strength / hardness class: ST
Thread code letter: M
Thread pitch: 1,5mm
Outside diameter: 48mm
Width across flats: 41mm. Screw fitting joint flange. Flange to drive pinion. E63. C300, C300 4-matic. Manual trans. Joint flange to crown gear. Joint flange threaded connection. Joint flange to bevel gear.

Diameter: 10mm
Strength / hardness class: 10.9
Thread code letter: M
Thread pitch: 1,5mm
Width across flats: 16mm.

Rear axle housing with differential. M 14 x 1,5. Differential gear. Right m 14x1,5.