80MM. 2,5X102MM
Diameter: 7,9mm
Inside diameter: 0,75mm
Outside diameter: 22 mm
Material thickness: 1mm. AERATION/VENTILATION. 2,5X102MM
Diameter: 7,9mm
Inside diameter: 0,75mm
Outside diameter: 22 mm
Material thickness: 1mm.

Mounting material. 2,5X100 MM. Adapter line fastening. 2,5x100 mm. Line mounting. 2,5X100 MM. Hose to engine hood hinge. 2,5x100 mm. Fastening, electrical line at connector housing. 2,5x100 mm.

Mounting of cable harness on frame. 5 mm / 3.6 x 200 mm. Fixture hose, for wheelhouse liner. 5 mm / 3.6 x 200 mm. Mounting, clutch cable. 5 mm / 3.6 x 200 mm.

Mounting material. 4.6 X 150 MM (D=5MM)
Diameter: 5mm
Material thickness: 1,2mm.

18.5 mm.

For hose to body. 20 mm. De-aeration line. 20 mm. Cable harness mounting. 20 mm. Wiring harness. 20 mm. Bracket mounting. 20 mm. Hose to engine. 20 mm. Mounting, vent lines to corrugated hose, right. 20 mm. Adapter cable to fan shroud. 20 mm. Filler neck. 20 mm. Breather line to engine. 20 mm.

To o2 sensor bracket. 23 x 24 mm. Left bracket. 23 x 24 mm.

Dome lamp cable harness. 9.5x13 mm. Mounting, cover. 9.5x13 mm. (fuel pipe to wheel arch panel angle). 9.5x13 mm. Line attachment. 9.5x13 mm. For fuel pipe at angle, wheel arch pan up to chassis 7519994. 9.5x13 mm.

Lambda sensor line mount. 18 X 14 MM. Cable conduit. 18 x 14 mm.

Cable harness at engine.

15 x 15 mm.

Oxygen sensor. 02 sensor upstream of catalytic converter. O2 sensor line.

Line mounting. 5 mm. Line aux.heater left rear seat floor. 5 mm. Damper strut delivery line. 5 mm. Pressure line to shock-absorber strut. 5 mm. Front brake cable to tunnel. 5 mm. Pipe line to wheelhouse. 5 mm. Rear floor assembly right. 5 mm. To right rear wheelhouse. 5 mm.

Bleed line mount. 2 X 8-9 MM. Bleed lines. 2 X 8-9 MM. Line holder. 2 x 8-9 mm. Hose. 2 x 8-9 mm. Purge line to ac line. 2 x 8-9 mm. Brake line to brake line. 2 X 8-9 MM.

Belt tensioner squib. 0.7 - 2.4 mm2. Green 0,7 - 2,4 mm2. 0.7 - 2.4 mm2.

SOLDERING SLEEVE. 0,13MM2 - 0,5MM2
Leitungsquerschnitt Min/Max: 0,13-0,5mm2. 0.5 MM2. 0,13MM2 - 0,5MM2
Leitungsquerschnitt Min/Max: 0,13-0,5mm2.

Oxygen sensor. 5 mm. Bracket mounting. 5 mm. Control module,auxiliary fan. 5 mm.

Holder

For sheet thickness 0.8-3.5 mm. 13X18 MMDiameter: -Inside diameter: -Outside diameter: -Material thickness: -. SENSOR LINE TO SHIELD. 13X18 MMDiameter: -Inside diameter: -Outside diameter: -Material thickness: -. TO LEFT REAR CRANKCASE, FOR ENGINE WIRING H ...

Ground cable. Ground lead and speed-sensitve power steering wiring harness.

Left seat frame locking mechanism. 5 mm. Fastening upholstery strip.

Sensor line. O2 sensor. Oxygen sensor contact.

Sensor line at left transmission bellhousing. Rear transmission case. Sensor cable to right transmission bell housing.

Adhesive strip. 100X70X3MM. Damping. 100X70X3MM. Loading floor,left. 100x70x3mm. Via screws to steering, left and right. 100X70X3MM. Left support. 100X70X3MM. On folding top case cover. 100x70x3mm. Rear seat bottom. 100x70x3mm. Below rear seat at left on cardan shaft tunnel. 100x70x3mm.

Sealing. To equipment compartment. 24.5x28.5 mm. 24.5 x 28.5 mm. To plug the free outlets at case. Control module box. Apparatus case and control units.

Firewall, front passenger side. Major assembly partition wall. 6-hole.

Rear panel door,right.

Brake line to transverse control arm, front left. Right front brake line to tunnel, bottom.

For weld stud T5. 4,6X155 MM. Insulation mounting. 4,6x155 mm. To line. 4,6x155 mm. Mounting material. 4,6X155 MM. Tank breather line. 4,6x155 mm. Line mounting. 4,6X155 MM. Return. 4,6X155 MM. Drain hose to body-in-white. 4,6X155 MM.

185 mm. 185 mm. 170mm. 185 MM. 150mm. 185 MM.

Cable harness mounting. 75 x 40 mm.

02 sensor to transmission. Oxygen sensor cable to transmission.

To right transmission case. Sensor line at right transmission bell housing. O2 sensor to transmission bell, right. Sensor cable to transmission bell right.